top of page

Raspberry Pi RP2350B/RP2354B SBC

Nov 9
6 min read

Updated: 23 hours ago

I have never worked with a Raspberry Pi microcontroller (MCU). In this series, I am going to take a shot at building a custom PCB for the RP2354B -- working towards a single-board computer (SBC). I have no specific goals other than getting familiar with this MCU and seeing how it compares to other MCUs I have used in the past. Here, I'll document my learning journey.


Two things seem like good starting places for me: read the datasheet and build a minimal board, based on the guidance in the hardware design guide. And while I wait for my custom PCBs and other parts to arrive, I can start to learn about the development environment using a Pico 2 board.



Key Components (first PCB)

  • RP2354B 80-QFN (or RP2350B 80-QFN without internal flash). Board jumpers to select.

  • TLV62569DBVR buck regulator

  • USB power & serial

    • USB-C connector

    • USB TVS ESD protection diode array

    • 5.1k pull-downs on USB CC1 and CC2

  • GPIO 0, 1 reserved for UART 0.

  • External 16 MB flash: W25Q128JVSIQ. For RP2350B, primary flash. QSPI_SS used for selection. Not populated on RP2354B.

  • External 8 MB PSRAM

    • Possible use as slower video memory

    • GPIO 47 used for selection.

    • APS6404L

  • LEDs for power, GPIO testing, possibly other indicators

  • Crystal and related passive components

  • Boot select & reset buttons

  • Debug header: SM03B-SRSS-TB

  • Expansion headers (GPIO, 5V, 3V3)

  • USB host

    • USB Type-A female receptacle

    • Two inline 27 Ohm resistors on the data lines

    • GPIO 10, 11

    • 5V power rail for V_BUS pin, protected by a 500 mA PTC fuse. Better: TPS2051 or AP2553. GPIO 3 for overcurrent fault.

    • TVS ESD protection diode array for signal safety

    • 15K pull-downs on D+/D-

    • Keyboard input

  • HSTX video

    • GPIO 12-19, differential pairs (100 Ohm)

    • TVS IC: TPD12S016

    • Type-A HDMI connector

  • SPI

    • Two SPI controllers.

    • Micro SD card (SPI 1). All other SPI devices on SPI 0. GPIO 2 for SD card detect.

    • Three GPIO for demux to support eight SPI devices on SPI 0: GPIO 44-46. Outputs length matched. 10k pull-ups. 74HC138 -- drive one of its enable inputs from GPIO , with a pull-up so nothing is selected at reset

    • SCK, MOSI, MISO

      • GPIO 4-7 for SPI 0 (uses demux for eight CS signals). GPIO 4 = MISO, GPIO 5 = software GPIO to control demux enable, GPIO 6 = SCK, GPIO 7 = MOSI.

      • GPIO 28-31 for SPI 1 (includes CS). GPIO 28 = MISO, GPIO 29 = software-based CS, GPIO 30 = SCK, GPIO 31 = MOSI.

    • W5500 Ethernet with GPIO 26, 27 for interrupt and reset

    • SPI display

  • Buzzer on GPIO20

  • I2C

    • GPIO 8, 9

    • RTC header

    • QWIIC header

    • EEPROM (configuration info)

  • WM8960 hat

    • Config via I2C

    • I2S on GPIO 21-25. GPIO 21 MCLK (clock output), 22 BCLK, 23 LRCLK, 24 DAC data, 25 ADC data.

  • Decoupling capacitors

  • Unused pins to headers

    • GPIO 32-43 available.

    • GPIO 40-43 could be used for ADC inputs.

  • PCB

    • Four-layer PCB with inner GND layer, inner power layer (mostly 3V3 with some 5V0). Top and bottom layers GND filled. 100x100 mm max.



Next Steps

I'm not sure what this board will eventually look like, but given the above brainstorming, here's what Gemini is envisioning. :)


For next steps, I'll start with building out the majority of the schematic, followed by PCB layout. I can then order PCBs and components, assemble the PCB, and transition into software development.




RP2354 SBC: Project Kick-off



Step One: Schematic

I'm looking at two build configurations for the PCB:

  • Primary configuration (RP2350B): External 16 MB flash plus external 8 MB PSRAM. QSPI_SS and GPIO 47 will be used as the two CS signals.

  • Secondary configuration (RP2354B): Internal 2 MB flash plus external 8 MB PSRAM. The external flash is unpopulated.

So far, I have sketched out the following pin assignments.

Pin Name Assignment

1 GPIO4 SPI0 MISO

2 GPIO5 74HC138 enable (software GPIO, pull-up)

3 GPIO6 SPI0 SCK

4 GPIO7 SPI0 MOSI

5 IOVDD 3V3

6 GPIO8 I2C0 SCL (RTC, QWIIC, EEPROM, WM8960, HDMI)

7 GPIO9 I2C0 SDA (RTC, QWIIC, EEPROM, WM8960, HDMI)

8 GPIO10 USB host D+ (PIO-USB)

9 GPIO11 USB host D− (PIO-USB)

10 DVDD 1.1 V core (from VREG)

11 GPIO12 HSTX: TMDS pair A

12 GPIO13 HSTX: TMDS pair A

13 GPIO14 HSTX: TMDS pair B

14 GPIO15 HSTX: TMDS pair B

15 IOVDD 3V3

16 GPIO16 HSTX: TMDS pair C

17 GPIO17 HSTX: TMDS pair C

18 GPIO18 HSTX: TMDS pair D

19 GPIO19 HSTX: TMDS pair D

20 GPIO20 Buzzer (PWM)

21 GPIO21 WM8960 MCLK (GPOUT0)

22 GPIO22 I2S BCLK

23 GPIO23 I2S LRCLK

24 IOVDD 3V3

25 GPIO24 I2S DAC data (to WM8960)

26 GPIO25 I2S ADC data (from WM8960)

27 GPIO26 W5500 INT

28 GPIO27 W5500 RST

29 IOVDD 3V3

30 XIN 12 MHz crystal

31 XOUT 12 MHz crystal

32 DVDD 1.1 V core

33 SWCLK Debug header

34 SWDIO Debug header

35 RUN Reset button + pull-up

36 GPIO28 SPI1 MISO (SD card)

37 GPIO29 SD card CS (software GPIO)

38 GPIO30 SPI1 SCK

39 GPIO31 SPI1 MOSI

40 GPIO32 Expansion header

41 IOVDD 3V3

42 GPIO33 HDMI_TX_HPD

43 GPIO34 Expansion header

44 GPIO35 Expansion header

45 GPIO36 Expansion header

46 GPIO37 Expansion header

47 GPIO38 Expansion header

48 GPIO39 Expansion header

49 GPIO40_ADC0 Expansion header / ADC0

50 IOVDD 3V3

51 DVDD 1.1 V core

52 GPIO41_ADC1 Expansion header / ADC1

53 GPIO42_ADC2 Expansion header / ADC2

54 GPIO43_ADC3 Expansion header / ADC3

55 GPIO44_ADC4 74HC138 A0

56 GPIO45_ADC5 74HC138 A1

57 GPIO46_ADC6 74HC138 A2

58 GPIO47_ADC7 PSRAM CS (QMI CS1n, 10k pull-up)

59 ADC_AVDD 3V3 (filtered)

60 IOVDD 3V3

61 VREG_AVDD 3V3 (RC filtered, per design guide)

62 VREG_PGND GND

63 VREG_LX Core regulator inductor

64 VREG_VIN 3V3

65 VREG_FB To DVDD (filtered core output)

66 USB_DM USB-C D− via 27 Ω

67 USB_DP USB-C D+ via 27 Ω

68 USB_OTP_VDD 3V3

69 QSPI_IOVDD 3V3

70 QSPI_SD3 Flash + PSRAM SD3

71 QSPI_SCLK Flash + PSRAM SCLK

72 QSPI_SD0 Flash + PSRAM SD0

73 QSPI_SD2 Flash + PSRAM SD2

74 QSPI_SD1 Flash + PSRAM SD1

75 QSPI_SS W25Q128 CS (RP2350B build) + BOOTSEL button via 1 kΩ

76 IOVDD 3V3

77 GPIO0 UART0 TX

78 GPIO1 UART0 RX

79 GPIO2 SD card detect

80 GPIO3 USB host overcurrent fault (10k pull-up)

EP GND Exposed pad, ground


The most significant components I have identified:

Sheet Component Description LCSC Part #

Overview - -

MCU & Core Memory RP2350B or RP2354B MCU C42415655

W25Q128JVSIQ Flash 16 MB C97521

APS6404L-3SQR-SN PSRAM 8 MB C5333729

ABM8-272-T3 Crystal C20625731

Crystal passives

Buttons Boot Select, Reset C2889024

Configuration jumpers

SM03B-SRSS-TB Debug header C160403

AOTA-B201610S3R3-101-T Inductor for 1V1 C42411119

Power & USB-C USB-C receptacle C2988369

ESD Diode C7519

TLV62569DBVR Buck converter C141836

Video HDMI Type A receptacle C427307

TPD12S016PWR HDMI companion ESD C201665

USB Host USB Type A receptacle C2346

TPS2051 USB power switch C3231915

ESD Diode C7519

Audio Buzzer C162678

2N3904 Transistor C713605

Storage SD Card connector C2889258

SPI 74HC138 Demux 3-to-8 C5602

General SPI headers

W5500 header

I2C SM04B-SRSS-TB Qwiic header RA C160404

Qwiic header V C160390

RTC header

Expansion 2.54 mm headers


Plus all of the passive components to support the above, including decoupling capacitors, resistors, etc.


RP2354 SBC: Schematic, Major Component Rough-in

RP2354 SBC: Schematic First Pass Complete

Step Two: PCB Design

RP2354 SBC: PCB Layout and Routing, part 1

RP2354 SBC: PCB Draft Revision Complete


I have posted the full EasyEDA Pro project, Gerber files, and schematic to my GitHub.




[17 November 2026] Today, I ordered PCBs from JLCPCB. I ordered parts from LCSC and Mouser. Total cost for five PCBs, shipped, was under $6 USD. For parts, I generally ordered enough for five PCBs. Some parts had a minimum order quantity that was higher (e.g., capacitors often required ordering 50 or 100 pieces). Estimated total parts cost for a single PCB (low volume, does not include shipping): approximately $20. I expect it will be a few weeks before I receive everything.


Update: As I had a handful of smaller VIAs on v0.01, JLCPCB wanted to add $37 to the cost. Instead, I updated the PCB and increased the size of the smaller vias. I updated the DRC rules to set 0.3 mm as the smallest inner diameter and 0.4 mm as the smallest outer diameter. With this small change, the extra fee is not assessed. I marked this updated PCB as v0.02.


More to come!



Step Three: PCB Build & First Fire-up

...


Step Four: Software Stuff

Notes:

  • Change the SPI demux address bits only while the enable is inactive to prevent CS glitching on devices.




Resources

 
 
 

Comments


bottom of page